Pioneer ddj sb2 traktor 2 mapping

• Ddj Sb Traktor Mapping
• Ddj Sb2 Download Software
• Pioneer Ddj Sb2 Driver Serato

- Content -

I.Features:

• 4 Decks.
• Vinyl, (Scratch, bend) & Slip.
• Browser & Layout control.
• Tempo Fader & Tempo Range .
• Play, Backwards Playback, CUE
• Channel Fader Start/Cue.
• Gain, EQ & Monitor Cue .
• Levels, Channel Pre fader
• Sync Phase or Tempo & Phase.
• Filter knob, filter on/off, filter fader.
• 8 Hot Cue.
• Loops: Auto Loop, 'ROLL', Manual Loop, (size with Jog W.) & Cue Loops.
• 4 Fx control, single or Group & Mixer Fx control.
• Deck Focus control.
• Master Clock, Auto, On/Off, Set master, tap master tempo, set as Master tempo.
• Waveform zoom, single, all decks & reset.
• Key lock, key adjust, preserve key, reset key.
• Snap & Quant.
• Sampler, 16 Cells Full control
• Beat Jump.
• Loop Recorder.

II.Tweaks

III.Facts about Traktor

IV.SB2´s 'PAD TRANS'

V.The Track Loading Show

VI.DOWNLOAD

VII. Related Links

Color Legend:
* Control Not mapped in the SB2.
* Hold Modifiers, While they are press some other Pads, Buttons & Faders operate different features.
- When an operation requires the use of (HOT CUE+), (AUTO LOOP+) or (MANUAL LOOP+),
they can be press in any of the 4 Deck.
- In Remix Deck the use of (SAMPLER) as a modifier.& to trigger (Monitor Cue+) as a modifier,
& the use of (HOT CUE+), (AUTO LOOP+)&(MANUAL LOOP+)(from opposite Deck*). as native Remix modifiers.
- In Loop Recorder the use of (Shift+ SAMPLER) as a modifier.& to trigger (Monitor Cue+) as a modifier.
- In XFader the use of (Shift+ SAMPLER) as a modifier.& to trigger (Monitor Cue+) as a modifier.
* The use of a Modifier for Fx operations.
* If No comment, is crystal clear, so just press the button / Pad or twist that knob.

Features

- DECK:
4 Deck.

- VINYL:
If is 'ON' Scratch operation is possible when the Deck is playing. led will report state.
* VINYL acts as a nativemodifier in the SB2, (for the press Top of the Jog W.)

- SLIP:
* Traktor´s 'Flux mode'.

- Jog W.:
* Pressing Top acts as a native modifier in the SB2, (for Jog Turn).

• Jog Turn Top:

• If Deck is not playing _____________ Jog Turn. (Scratch).
• If Deck is not playing (Shift+) ______ REV/FWD. (Seek Position).
• If Deck is playing _______________ Pitch Bend. (if 'VINYL' is on it will Scratch).

_ Other use:

• MANUAL LOOP´s 'IN' or 'OUT' + Jog _____ MANUAL LOOP size. (Fine).

* Detailed informationin the 'MANUAL LOOP'´s section.

• Fx Button 1, 2 or 3 + Jog ______________ Single Fx knobs.

* Detailed information in the 'Fx 1, 2, 3 & 4'´s section.

• Jog Turn Side:

• If Deck is not playing ________________ Jog Turn. (trim)
• If Deck is not playing (Shift+) _________ REV/FWD. (Seek Position - trim)
• If Deck is playing __________________ Pitch Bend. (trim)
• If Deck is playing (Shift+) __________ Not mapped.

_ Other use:

• MANUAL LOOP´s 'IN' or 'OUT' + Jog _____ MANUAL LOOP size. (U.Fine)

* Detailed information in the 'MANUAL LOOP'´s section.

- Browser:

• Only Browser ___________ Press Encoder.
• Track Selector __________ Rotate Encoder. (if turned faster, it browses faster)
• Folder Selector _________ (Shift+) Rotate Encoder.
• Folder Collapse ________ (Shift+) Press Encoder.
• LOAD _________________ Load selected Track, or 'Remix Set' from library.
• Layout _______________ (MANUAL LOOP+) Rotate Encoder.

* If attempt to load a Remix Set in to a 'Track Deck', or a Track in to a 'Remix Deck', the Remix Set or the Track will not load.
* (AUTO LOOP+) ________ Rotate Encoder ________ Not mapped.
* (SAMPLER+) __________ Rotate Encoder ________ Not mapped.

* (MANUAL LOOP+) ______ Press Encoder ________ Not mapped.
* (SAMPLER+) ___________ Press Encoder _______ Not mapped.

- Play/Pause:
(Shift+) ________Play on pad release acting as a (CUP).
led on if Track is loaded and not playing or playing if (Shift+), if Deck is playing, led on (Beat Phase).
* No (CUP) involve, mapped with 'Cue' & inverse 'Play'.

- Backwards Playback: (at MANUAL LOOP [CUE LOOP])
(Only if Deck is playing)

• 'EXIT' ______ Plays backwards while press, returning to normal on pad release.

* After using the feature with the 'EXIT' pad, 'SLIP/FLUX' will end up always off.

• '1/2X' _______ Play backwards while press, returning to normal on pad release.(Flux/Slip mode)

* After using the feature with the '1/2X' pad 'SLIP/FLUX' will end up always on
* If used inside an active Loop the 'SLIP/FLUX' will kick in and the Loop will be exit if Pad. is not released before crossing the 'Loop out' marker.
- Cue:
If Deck is not playing & a Track is loaded, led will be on, if Deck is playing led will be on only if Tack is in phase with the Master or if is the master, led will be on all the time.

• If Deck is playing __________________ Stops Deck & jumps back to Cue.
• If Deck is not playing ______________ Sets Cue.
• If Deck is not playing (Shift+) ______ Returns to previous Hot Cue (auto repeat).

* If (Shift+) is done from an active stored Loop it gets stuck there and will not jump to previous Hot Cue.. go figure :-/

- Vinyl Pause & Jump Back:
(Shift+) CUE preform few actions between press and release.
* Track Tempo must be Set to '0' to successfully use this 'trick'.

• On Pad press, creates & stores 'Hot Cue 8', and It slowly pitch down the Track to -100% tempo until it stops, it takes around 3 seconds if u do not release the CUE Pad.

• On Pad release it jumps back to previously created 'Hot Cue 8' to start playing and deletes it.

* If 'Hot cue 8' already exists, it will jump to it on Pad press, then it will pitch down and it will start playing on Pad release
from 'Hot Cue 8', to then delete it.
* If made inside a Loop deactivates Loop on Pad release.
* Do not store a any Cue in 'Hot Cue 8' if u want this feature to work correctly.
* Scratch is not possible in the middle of this operation.
* For the complexity of the 'macro', If tapped to fast, could happen that it will not have time to create Hot Cue 8 and it will
jump to what ever previous Hot Cue is stored, if a Hot Cue is not stored it will jump to the Grid Marker, (usually at the
beginning of the Track), it will not go further than what ever previous Hot Cue is stored.
- CH Fader Volume:

- CH Fader Start:
- If Deck is playing:

• Jump back to Cue ____ (Shift+) Channel Fader (from 'X' to '0').
• Starts playing ________ (Shift+) Channel Fader (from '0' to 'X').

- If Deck is not playing:

• Create Cue ___________ (Shift+) Channel Fader (from 'X' to '0').

- Gain:
- EQ,: (low-mid-high)

- Monitor Cue:
It will activate by press or when a Track or Remix Set is loaded.
* If attempt to load a Remix Set in to a 'Track Deck', or a Track in to a 'Remix Deck', the Remix Set or the Track will not load but the Monitor Cue will turn ON.
* Even when the Button in SB2 gives a different value if pressed (Shift+), led here seems to have just 1 output,(if 'Monitor Cue' is on, the led will be on even when pressing shift).

- Head Phones Mix:
(only from Deck A or C)

• Head Phones Volume _____ Shift + SAMPLER + Monitor Cue +HEADPHONES MIX knob.

* Once Monitor Cue is press, Shift+ SAMPLER can be released, and with Monitor Cue Still Press we proceed to operate the HEAD PHONES MIX Knob.
Volume State will be reported in the CH LEVEL (every Deck), when the light just reach Yellow the level in traktor will be at its default.
* If Deck is playing, still the Volume can be adjusted but the led will report overlapping with the Level Channel.
* SB2 has a powerful native 'headphones level'.
- Channel Level :
- Pre Fader

• At '0 db' red pic lights steady
• At '-0.3 db' red pic start flashing,
• At '-0.4 db' red do not show up.

* Test made with a '0 db' test tone. DOWNLOAD HERE!
- Sync:

• Sync Pad ____________ Phase Sync, (it does not Sync tempo),
• (Shift+) Sync Pad _____ Tempo and Phase Sync. led will provide feedback.

- Filter:

• Filter on/off ______ (Shift+) Monitor Cue.
• Filter knob ______ Only works if filter is on.
• Filter fade ______ Only works if filters are on.

* 'Filter Fade' is related to filter controls in a native way in the SB2, it does not need to be mapped

- XFader:
(only from Deck A)

• XFader Curve ______ Shift + SAMPLER + Monitor Cue + Filter knob. (Deck A)

* Once Monitor Cue is press, Shift+ SAMPLER can be released, and with Monitor Cue Still Press we proceed to operate the Dry/Wet knob (SB2´s Filter Knob In Deck A).
Curve State will be reported in the CH LEVEL (All Decks).
* If Deck is playing, still the Curve can be adjusted but the led will report overlapping with the Level Channel.
- Assignment:
(only from Deck A)
*In a logical way, Deck A & C in the Left side and Deck B & D in the Right side.

• Shift + SAMPLER + Monitor Cue + Pad ('IN', 'OUT', 'EXIT' or '1/2X').

led will provide feedback while Modifier is press.
* Once Monitor Cue is press, Shift+ SAMPLER can be released, and with Monitor Cue Still Press we can proceed to operate the Pads.
*In an inverted way, Deck A & C in the Right side and Deck B & D in the Left side.

• Shift + SAMPLER + Monitor Cue, (releaseShift+SAMPLER but do not release Monitor Cue), then with Monitor Cue Still Press, proceed to press Shift + Pad ('IN', 'OUT', 'EXIT' or '1/2X').

led will provide feedback while Modifier is press.

- Hot Cue & [Hot Cue 5-8]:
Create Hot Cue, (Shift+) pad delete Hot Cue., led on if Hot Cue is stored.
* If created inside an active Loop, it stores the Loop.
* Deletes Stored Hot Cue, only if is a Cue or a Loop.
* The proper use of Hot Cue 1 requires the tweak of settings, for more information go to the 'Tweaks' section.

- AUTO LOOP:
* glitch Loop if Deck is not playing.., if the Loop is made when snap mode is on, and the 'Loop in' is 'snapped' just after the reader, the led will not light up and the Loop will not be deactivate by pressing the pads, only the size will change when pressing the pads until the reader is located inside the Loop, with the Jog W., with the mouse, or just by pressing play.
* when using this feature the Cue will be overwrite for the last 'Loop in' marker.

• Loop size is = 1 _________ 'IN'.
• Loop size is = 2 ________ 'OUT'.
• Loop size is = 4 _______ 'EXIT'.
• Loop size is = 8 ______ '1/2X'.

• Move Loop back _______ (Shift+) 'IN', (auto repeat only works if 'Slip' is off)
• Move Loop forward ____ (Shift+) 'OUT', (auto repeat only works if 'Slip' is off)

• Size Loop /2 ______ (Shift+) 'EXIT', led on if Loop size is = 16
• Size Loop x2 _____ (Shift+) '1/2X' , led on if Loop size is = 32

led will provide feedback. when (Shift+) it will refer only to size

- AUTO LOOP [ROLL]:
It Loops while pressing, when stop pressing it keeps playing from it where suppose to be playing if pad would not had been press (mapped with 'SLIP' feature, called in Traktor 'FLUX'). The size can be change while the 'ROLL' is press by rotating the Encoder, (Browser´s Encoder).

• Loop size= 1/8 ________ 'IN'.
• Loop size= 1/4 _______ 'OUT'.
• Loop size= 1/2 ______ 'EXIT'.
• Loop size= 1 _______ '1/2X'.

led will be on, when not pressing, if 1 of the 4 Pads is press they will flash in Beat Phase.

* (Shift+) 'IN' _______ Not mapped.
* (Shift+) 'OUT' _____ Not mapped.
* (Shift+) 'EXIT' _____ Not mapped.
* (Shift+) '1/2X' _____ Not mapped.

*Press one of the 4 pads, while not releasing the firs Pad, is possible to chain it with the other 3 pads, once a pad is release, the Loop goes inactive, (not like in Serato, where u can keep chaining the pads for ever).. anyways, is possible to change the size of the 'ROLL' by operating the encoder of the browser while 1 of the 4 Pads is press.
* when using this feature the Cue will be overwrite for the last 'Loop in' marker created for the last 'ROLL' press.
* when 'ROLL' is in use is possible to Scratch or bend the 'ROLL'. (very cool)
* when Using 'ROLL' feature the 'SLIP/FLUX 'will end up always turned on.

- MANUAL LOOP:

• Set 'Loop in' ________ 'IN' (If Loop is not active).
• Set 'Loop out' ______ 'OUT' (If Loop is not active).

- If Loop is active, but there is not a Loop, Set 'Loop out' makes Loop not active the first time is press, the second time it will set the 'Loop out'. :-/

(This could happen if a 'Loop in' is set and the 'Loop out' is not set, and then we press 'EXIT', in this case, Exit will work as a cup and it will activate the Loop even when there is not a loop.
* 'Loop in' & 'Loop out' needs the condition 'Is In Active Loop.Deck X', this way the size can be operated in an active loop, how ever this condition can make the 'IN', 'OUT' & 'EXIT' to stop working in the SB2 if:
a) ___ if 'Loop in' & 'Loop out' are set at the exact same point.. go figure:-/
b) ___ if from inside an active Loop the Track is rewind with the Jog W., the mouse, or the 'Beat Jump' and then the 'OUT' Pad is tapped 2 times, or the OUT in Traktor is clicked 2 times with the mouse.
* Not likely to happen, but if in any case it happens the solution is (Shift+) 'Exit'. When not using the condition 'Is In Active Loop.Deck X' in Pads 'IN' & 'OUT' this issue does not happened, but then is not possible to control the size of a loop with the Jog W., maybe is just a bug of the version of Traktor that was used to create this midi map (v.2.6.8),.. go figure:-/

- Loop size using Jog W.:
If Loop is active press 'IN' or 'OUT' + 'Jog W. turn' to fine the size, or the side of the Jog W. to ultra fine the size. (fine size will only works if 'VINYL' is off, if 'VINYL' is on, it will Scratch).
* The size selector will notchange when resizing Loops with the Jog W., so if the Loop after is resized using the Jog W. is resized again using the incremental, (pads 1/2X or Shift+ 1/2X), the size will jump to the previous Loop size set before the Loop size was modified by the Jog.W.

• Moves the Loop backwards _____ (Shift+) 'IN'
• Moves the Loop forward _______ (Shift+) 'OUT'

* Distance of the move = Loop size
* 'auto repeat' only works if 'SLIP' is off.., go figure:-/

• 'EXIT'

- If Deck is playing..
.. & Loop is active _______ makes Loop inactive.
(If is playing outside the Loop, it jumps back to 'Loop in' marker.)
.. & Loop is not active ___jumps back to 'Loop in' marker and activates Loop.
(If there is not a 'Loop out', it jumps back to 'Loop in' marker, (or Cue) acting as a 'CUP'.)
led on if Loop is active, if is not playing inside an active Loop in it will flash in Beat Phase.
- If Deck is not playing _______ Toggle Loop Active.

• (Shift+) 'EXIT' ___________ Toggle Loop Active, led will report Loop state.
• '1/2x' __________________Size 1/2, led is on if Loop size=32
• (Shift+) '1/2x' ___________ Size x2, led is on if Loop size=32

- MANUAL LOOP (CUE LOOP):

• Store Loop as 'next Hot Cue' _______ 'IN'(if Loop is active)

• Delete current 'Hot Cue' ___________ (Shift+) 'IN'.

* Caution!!!, it will delete even the beat grid if the Tack was analyzed with the option 'Store Beat Marker as a Hot Cue', for more information about it go to the the 'Tweaks' section.

• Jump to prev. 'Hot Cue' ______ 'OUT', (if Deck is not playing), if Deck is playing it acts as a (CUP).

*if Deck is playing & Loop is active it will not go to previous 'Hot Cue' from this Loop , (it will just 'CUP' the current 'Hot Cue'), if Deck is playing & Loop is not active´, is possible to jump to previous Hot Cue by tapping the pad.

• Jump to Next 'Hot Cue' _______ (Shift+) 'OUT'.
• 'EXIT' _____________________ (used for backwards playback)
• '1/2X' _____________________ (used for backwards playback)
• (Shift+) 'EXIT' ______________ Not mapped.
• (Shift+) '1/2X' ______________ Not mapped.

- Fx unit (Mixer) 1 2 3 & 4:
(From each Deck)

• Fx1 on/off __________(HOT CUE+)'IN'.
• Fx2 on/off __________(HOT CUE+)'OUT'.
• Fx3 on/off __________(HOT CUE+)'EXIT'
• Fx4 on/off __________(HOT CUE+)'1/2X'.

led will provide feedback while Modifier is press.

- Fx 1, 2, 3 & 4:
- Routing selector:
(Only from Deck A)

• Insert __________(AUTO LOOP+)Pad ('IN', 'OUT', 'EXIT' or '1/2X').
• Post Fader ______(AUTO LOOP+)Shift+ Pad ('IN', 'OUT', 'EXIT' or '1/2X').

..Pad 'IN'=Fx1, Pad 'OUT'=Fx2, Pad 'EXIT'=Fx3, Pad '1/2X'=Fx4, (same when Shift+)
led will provide feedback while Modifier is press.
- if the Fx is 'Insert', when '(AUTO LOOP+)' is press the led will be on.
- if the Fx is 'Post fader', when '(AUTO LOOP+)Shift' are press the led will be on.

• Reset Fx LFO ___________(AUTO LOOP+)Press Encoder. (from any Deck)
  

• Switch Fx 1 & 3 __________ (Shift+) 'DECK' (A or C).
• Switch Fx 2 & 4 __________ (Shift+) 'DECK' (B or D).

led in 'PAD TRANS TAP' Button If (shift+).
led dime if Fx 1 or Fx 2 selected, led on if Fx 3 or Fx 4 selected.
* Led will fail to report if (Shift+) 'PAD TRANS TAP' is press. it should not be press since is not mapped, but may be press if the 'Trans Pad Fx' is goIng to be used, (if was activated by Serato first), then the command will be require to program the speed at witch the 'PAD TRANS Fx' is going to perform, so then u shall relay in the next 'way':
* Other way to know what Fx is focus in the SB2´s Fx section 1 or 2, is to always have in Fx 1 & 3 a different Fx, one single Fx, and 1 group Fx, (same for Fx 2 & 4), this way when pressing shift, still Fx will report if they are single or group by flashing the led in different ways.

• Toggle Fx Single/Group Fx 1 & 3 _______ (Shift+) LOAD A & C. (Left Deck)
• Toggle Fx Single/Group Fx 2 & 4 _______ (Shift+) LOAD B & D. (Right Deck)

When Pressing the Shift pad, the Fx Buttons will flash in Beat Phase (device target):
If group Fx: the 3 Buttons will flash chasing each other.
If single Fx: Button 1 will flash in Beat Phase.
* led will fail to report if all Decks are in pause.

_Group Fx:

• Dry/Wet _________ (Shift+) 'LEVEL [BEATS]' knob.
• Fx knobs _______ 'LEVEL [BEATS]' knob (Macro).
• Fx On/Off _______ Fx Button(1,2 & 3)
• Select Fx _______ (Shift+) Fx Button(1,2 & 3)

The 3 Buttons will flash in Beat Phase, (device target), chasing each other while any of the 'SHIFT' pads are press.

_Single Fx:

• Single fx on/off _____ 'FX'´s Button 1 + Button 2
• Dry/Wet ___________ LEVEL/BEATS Knob
• Fx Button 1 _______ (Shift+) Button 1 (Reset Fx)
• Fx Button 2 _______ (Shift+) Button 2
• Fx Button 3 _______ (Shift+) Button 3
• Store preset ________ 'FX'´s Button 1 + Button 3
• Select Fx 1 or 3 _____ 'FX1'´s Button 1 + tempo Fader. (Deck A or C)
• Select Fx 2 or 4_____ 'FX2'´s Button 1 + tempo Fader. (Deck B or D)
• Fx 1 & 3 knobs _____ 'FX1'´s Button (1, 2 or 3) + Jog w. Deck A & C

* Operation only possible from Deck A or C, 'VINYL' must be OFF in the Deck of the operated Jog W.

• Fx 2 & 4 knobs _____ 'FX2'´s Button (1, 2 or 3) + Jog w. Deck B & D

* Operation only possible from Deck B or D, 'VINYL' must be OFF in the Deck of the operated Jog W.

• (Shift+) 'LEVEL [BEATS]' _____ Not mapped.

- Deck Focus:
The 'Shift pad' of any Deck will focus this Deck, (if the Deck is playing), or what ever other Deck is playing if is press in a Deck that is not Playing.
Added to help with led feedback on Single or Group Fx.

Ddj Sb2 Download Software

* On Pad press it will focus on what ever Deck is playing, to make sure the Fx´s led will provide feedback.
* On pad release it will focus the Deck that the pressed Shift button belongs to. (only if this Deck is playing).

- Tempo:

• Tempo fader _____ It works with or without (Shift+).

* Soft take over do not work when used (Shift+), tested with 'key adjust' & 'Wave form zoom'.

• Tempo Range _____ led on at 8% & 100%.

- Master Clock:
* No midi map for the panel 'Master Clock' / 'FX' in Traktor, a work around could be to make a new layout.

• AUTO on/off ___________(HOT CUE+)Sync, led will report state while modifier is press.
• Set MASTER __________ (AUTO LOOP+) Sync, led will report state while modifier is press.
• Tap Master Tempo _____ (MANUAL LOOP+)(keep it press and then tap) Sync.

- Set as master tempo:

• (HOT CUE+) DECK, led on if Deck is Master in 'Shift Pad'.

* (HOT CUE+) DECK, booth buttons must be press in the same Deck, if not the Master will be the flip side Deck. of the 1 trying to set as Master.

- Waveform Zoom:

• Waveform zoom (A,B,C or D) ______(HOT CUE+)Tempo Fader.
• Waveform zoom (all Deck) _______(HOT CUE+)Rotate Encoder.
• Reset size (all Deck) ___________(HOT CUE+)Press Encoder.

- Key Lock:

• Key Lock (Preserve Pitch) _____(HOT CUE+)KEY LOCK.
• Key Reset __________________(AUTO LOOP+)KEY LOCK.
• Key Adjust_________________(AUTO LOOP+)Tempo Fader.

'KEY LOCK' led will be On if key value is = to '0', while the Modifier is press.
* Preserve Pitch only works if Deck is Playing, and off course only if Key lock is off.

- Snap & Quant:

• Snap______(HOT CUE+)(Left) VINYL (Deck A or C)
• Quant _____(HOT CUE+)(Right) VINYL (Deck B or D)

led will give feedback while the Modifier is press

Pioneer Ddj Sb2 Driver Serato

- SAMPLER (Remix Deck):
(Only Remix Deck C & D)

• 16 Cells Control Sampler grid.

* Only the 16 Cells from Page 1 can be controlled.
* Pages where used in the conditions, to be able to control the 16 Cells from just 4 pads.

* 8 pads controllable simultaneously if Remix Deck is set in Deck C & D

• Select Sample Page 1 _____(SAMPLER+)Pad 'IN'.

* Page 1 will control the 1rst horizontal line of Cells prom Page 1.

• Select Sample Page 2 _____ (SAMPLER+) Pad 'OUT'.

* Page 2 will control the 2nd horizontal line of Cells prom Page 1.

• Select Sample Page 3 _____ (SAMPLER+) Pad 'EXIT'.

* Page 3 will control the 3rd horizontal line of Cells prom Page 1.

• Select Sample Page 4 _____ (SAMPLER+) Pad '1/2X'.

* Page 4 will control the 4rt horizontal line of Cells prom Page 1.
led will provide feedback while Modifier is press.
Led Bug:
led will provide feedback while Modifier is press, (only to trust if the Cells are not in playing state, or maybe if they are in playing state but the Remix Deck is not playing).., when Pressing the 'modifier', (SAMPLER+), to specify what layer are the Pads going to control, the led will report correctly, but it will rapidly fade with the playing state of the playing Cells on this specific layer. (because of the Beat Phase led when on play state & the lack of conditions).

* The modifiers for Sampler Cell 'Load, Capture & Reverse' are mapped in the opposite Deck:
- if operating Remix Deck C, the opposite Deck would be Deck B or Deck D.
- if operating Remix Deck D the opposite Deck would be Deck A or Deck C.

- If Deck is not playing:

• Set Flavor to 'Track Deck' _______(SAMPLER+)HOT CUE.
• Set Flavor to 'Remix Deck' _______(HOT CUE+)SAMPLER.
• Load cell sampler from library __ (HOT CUE from opposite Deck*) + Pad ('IN', 'OUT', 'EXIT' or '1/2X').
• Capture from source _____(AUTO LOOP from opposite Deck*)+ Pad ('IN', 'OUT', 'EXIT' or '1/2X').

- If Deck is or is not playing:

• Select Source _____ (AUTO LOOP from opposite Deck*) + (SAMPLER).

- If Deck is playing:

• Reverse sampler _____ (MANUAL LOOP from opposite Deck*) + Pad ('IN', 'OUT', 'EXIT' or '1/2X').

* Reverse in Tractor: It reverse playback while pressing, going back to normal playback on Pad release, (if the modifiers was kept press during the operation), if the Pad is released after the modifier it will keep backwards on Pad release.
- If Deck is or is not playing:

• Trigger Sampler, (if loaded Cell) _____ Pad ('IN', 'OUT', 'EXIT' or '1/2X').
• Stop cell, _______________________ (Shift+) Pad ('IN', 'OUT', 'EXIT' or '1/2X').

• Quantize Remix Deck ______(SAMPLER+)Sync.
• Quantize Selector ________ (SAMPLER+) Monitor Cue+ Rotate Encoder.

• Slot Filter On/Off ______ (AUTO LOOP+) + Pad ('IN', 'OUT', 'EXIT' or '1/2X').
• Slot Filter knobs _____ (SAMPLER+) Monitor Cue + filter & eq knobs.
• Slot Volume _______(SAMPLER+) (Monitor Cue from opposite Deck*) + eq knobs & filter knob.

led will provide feedback while Modifiers are press.
* If (SAMPLER) from Deck D is a bit far away from Monitor Cue?, use (SAMPLER) button from opposite Deck.

• Slot Fx On/Off ______(HOT CUE+) Shift + Pad ('IN', 'OUT', 'EXIT' or '1/2X').
• Slot Punch On _____(AUTO LOOP+), Shift + Pad ('IN', 'OUT', 'EXIT' or '1/2X').

Slot Key Lock ____(HOT CUE+), (AUTO LOOP+), (MANUAL LOOP+), or(SAMPLER+) + KEY LOCK
Slot 1, Slot 2, Slot 3, Slot 4.
led will provide feedback while Modifiers are press.
* Since all 4 modifiers share the same M2 with different states, 'Slot Key Lock' Toggle must be executed 1 by 1
led will provide feedback on Cell state, off if Cell is empty & on if Cell is loaded.
If a Cell is playing, it will flash in Beat Phase while the Deck is playing.
If Deck is not playing and the Cell is loaded, the led will be on.
If Shift is press the Cells in playing state will have led on, led will show off when the Cells are not in playing state.
If a Cell is in waiting state led will be off.

• Slot Play Mode _______(SAMPLER+) Monitor Cue + Pad ('IN', 'OUT', 'EXIT' or '1/2X').
• Slot Trigger Type _____(SAMPLER+) Monitor Cue + Shift + Pad ('IN', 'OUT', 'EXIT' or '1/2X').

led will provide feedback while Modifiers are press, (only to trust if the cells are not in playing state, or if they are in playing state but the Remix Deck is not playing).., (because of the Beat Phase led when on play state & the lack of conditions).
* 'Slot Play Mode' & 'Slot Trigger Type ' work on samplers just after loading them, or just after playing them, but i must insist, that the led information is not to trust in any of the 2 cases if the cells are in playing state.

- Loop Recorder: (at SAMPLER [BANK])

• Size _____4 (Shift+) 'IN', 8 (Shift+) 'OUT', 16 (Shift+) 'EXIT', 32 (Shift+) '1/2X'

led will provide feedback while Modifier is press.

• Rec, _________'OUT'.
• Play/Stop _____'IN'.
• Dry/Wet ______Shift+(SAMPLER+) Monitor Cue +(A or C) + Filter knob (A or C).

* Once Monitor Cue is press, Shift+ SAMPLER can be released, and with Monitor Cue Still Press we can proceed to operate the Dry/Wet knob (SB2´s Filter Knob).

• Delete _____'1/2X'.
• Undo ______'EXIT'.

- Beat Jump: (at SAMPLER)
* Only if Deck Flavor is 'Track Deck'.
* If 'SLIP'is on the beat jump will jump only while press.

• Jump Size Dec. __________'IN' Pad, led on if size = Fine, 1/4, 4, 8, 16, 32
• Jump Size Inc., __________'OUT' Pad, led on if size = Fine, 1/16, 1/2, 32.
• Beat jump backwards, ____'EXIT' Pad, led on if size = Fine, 1/16, 1/8, 1, 16, 32.
• Beat jump forward, ______'1/2X' Pad, led on if size = Fine, 1/16, 1/8, 2, 32.*

* led:

* Cue Play (CUP) Mode:
- 'Exit' pad in MANUAL LOOP, (mapped with (CUP).
'Exit' pad in MANUAL LOOP will not work correctly unless the Traktor settings are adjusted to instant:
* Hot Cue:
The use of Hot Cue 1 require the tweak of the settings:
settings/analyze options/store 'beat marker as a Hot Cue' [uncheck])


* To learn about traktor settings i recommend u 'this awesome guide'

Facts about Traktor

Tempo vs tone: Every time a 6% of a tune's tempo is add or subtract ,the Track will move up or down one semitone. (1note)
Key Lock Feature:
In 'Scratch mode' key lock will work between -35% to +50 % (tempo adjust)
In 'Normal Mode' key lock will work between -90% to +100% (tempo adjust)

*In slow systems: using Hi quality option in 'key lock', could produce 'artifacts' in the sound when the 'key lock' is active, and there is any interaction with the 'Wave Display', using the jog w. or the mouse, this interaction could cause Traktor´s 'CPU load' indicator to go 'RED',..

The use of 'Hi quality key lock' minimizing the use of CPU, could be achieve, (depending on the system), by setting 'Mode Scratch' instead 'Mode Normal')
- Traktor does not recognize double tap, as a different command.
- When 'FLUX' is on, (SB2´s 'SLIP'), the behavior of some features will change.
_Scratching inside a Loop, will exit the Loop if Jog.W. is not released before the 'FLUX' marker cross the 'Loop out' marker.(same happens with the mouse).
_Hot Cue/Loop & beatjump will only jump while press, jumping back to 'Flux' marker on pad release.
- No Deck Tap Tempo, just Master clock TAP Tempo.
- No Vinyl Fx when stooping a Deck, it could be achieve by using an Fx, or if Tempo Range is set to 100% by moving the Tempo Fader to '0l'. (fast & smooth).
- No flashing state for led,the (on/off), can be achieve by using 'Beat Phase' or 'Levels' output, (still in booth cases the flashing state will depend from a Track running in Traktor, and if using 'Levels', it will also depend from the volume of the signal used)
_The amount of outputs that is possible to add in to a midi map seems to be huge,however, the number of'Beat Phase' outputs seems to be limited for the USB connection, the 'Beat Phase' number of outputstransmitted simultaneously could be limited by modifiers, (when the use of conditions involving the modifier will decide if the information is transmitted or not to the midi controller), but in the case of a controller like the SB2, with so many native layers the number of 'Beat Phase' outputs that can be transmitted simultaneously could be huge, in a point i had added so many 'Beat Phase' outputs, (most of them duplicated, so like this they are also working when the shift is pressed), that was needed to reassigning many of the outputs that where flashing on/off with a more humble output (no so many 'Beat Phase'). The symptoms where that if the 4 Decks where playing at the same time, the controller turned choppy, issue fixed by just changing the 'Out Port' of the map to'none'.

SB2´S PAD TRANS

Is ridiculous to map the PAD TRANS in Traktor since all 4 pads of each Deck are giving the exact same midi value..,

Also the 'PAD TRANS' feature, the 'Channel Volume' and the 'TAP' feature are related internally in the SB2. The 'PAD TRANS' will work in Traktor, (or probably in any other Dj Software), but only if activated first with Serato.
- The 'PAD TRANS' (SB2´s Fx feature) can be activated with 'Serato Intro' or 'Serato DJ', (probably with any version of 'Serato').



_ with 'Serato DJ' to just open the application is enough to activate the 'PAD TRANS', then close 'Serato DJ', do not unplug the SB2 from the computer and open Traktor. (Every time the 'PAD TRANS' is turned on, will be required to tap the tempo to make it work, (Shift+) 'PAD TRANS[TAP]', because every time that is turned off the pads will reset)
_ with 'Serato Intro' a Track with analyzed bpm must be loaded in to every Deck to activate the 'PAD TRANS', then close 'Serato Intro', do not unplug the SB2 from the computer and open Traktor. (Every time the 'PAD TRANS' is turned on, will be required to tap the tempo, (Shift+) 'PAD TRANS[TAP]', to make it work properly, because every time that is turned off the SB2 will recall the tempo of the Track used in Serato to activate the 'PAD TRANS').
Once the 'PAD TRANS' is activated in the SB2, it will work in Traktor, (and probably in any other Dj Software), if at least the 'Channel Volume' is midi mapped).

* Serato 'LOOK DOWN' PROBLEM: After plugging the 'SB2' to the computer, before opening 'Serato Intro or DJ', the secondary layers of the Performance Pad: 'HOT CUE [HOT CUE 5-8]', 'AUTO LOOP [ROLL]', 'MANUAL LOOP [CUE LOOP]', 'SAMPLER [BANK]', are accessible, but after opening 'Serato' this layers are 'lock down', and not accessible any more, is required to unplug the 'SB2' from the computer and then plug it again to make all this layers accessible again. To be able to access this secondary layers of the 'SB2' after using 'Serato' without the need of unplugging the controller from the computer, make active in Traktor´s 'Controller Manager' this..

'Fix midi map' DOWNLOAD

(This Download is already included in the Main Download at the bottom of the document)

(used 1 modifier per layer, so like this they will not interfere with each other).
Important: Import this midi map using the option in:
'Controller Manager' window import TSI import other
(if importing using the import option next to setup wizard all your settings could be lost).
- The Fix has a Glitch if Serato is not open first:
With this midi map 'Fix' active, if Traktor is open with 'frees controller state', (if 'Serato' was not opened first), is required to press (Shift+) one of the four layers in the 'SB2' before starting playing any Track.., or (Shift+) 'HOT CUE'.., or (Shift+) 'AUTO LOOP'.., or (Shift+) 'MANUAL LOOP'..or, (Shift+) 'SAMPLER'.. (in any of the Decks), the first time doing so the 'SB2' will make all led flashing like when recognizing software, what by the way will activate in the 'SB2' the led show in a Deck every time a Track is loaded)..

The Track Loading Led Show

In Serato every time a Track is loaded in to a Deck, all led of this Deck will flash chasing each other.
There is 2 ways to achieve the same behavior in Traktor, by opening Serato first, it will activate the feature in the SB2, so if u close then Serato, do not unplug the SB2 from the computer and open Traktor (or maybe in any other dj software), u still will get the led show when loading a Track in to a Deck, but remember that Serato Lock Down the Secondary layers of the Sb2.. so u still will need the 'Fix' midi map'. (if this fix midi map is active, the 'led show' will show up in traktor the first time that (Shift+) 'HOT CUE'.., or (Shift+) 'AUTO LOOP'.., or (Shift+) 'MANUAL LOOP'..or, (Shift+) 'SAMPLER' is press.. (in any of the Deck). (and after that, every time a track is loaded).

:
- Pioneer DDJ-SB2 Fix.
- Pioneer DDJ-SB2 Midi Map.

To program this map, as to put the guide together, costed me a huge amount of time,
it is a free download.., after u try it, if u find it useful, consider leveling your karma by making a humble donation..
Donators will get by email a version of the Midi Map with all the description boxes filled, (alphabetically by feature), as a document explaining how the modifiers where used..
CAUTION!!!:
I was chained to a sofa for around 80 days, and nothing is for free in this planet, u are going to pay for it one way or another, u can make a humble donation or expect for the universe to come after u with the 'bill'... your call..

Related Links:

• Pioneer Dj 'DDJ-SB2':

• Traktor Pro:

• I got my gear in:

I give them some Credit, because the customer service was outstanding, they had to send me the SB2 3 times!, because of some led not working properly, what means that they had to pay for the sending of the device 5 times!, i guess that was finally Pioneer who had to pay for the broken dishes..

• Knowledge Sources:

Art Concept by ijns

• Video 1

• Video 2

prev next

This product is currently unavailable for delivery to your country

Weekly 2019-06-17T18:07:50.820Z weekly. Hulasatul hulasa ismet pdf. YouTube Premium Loading. Get YouTube without the ads. Skip trial 1 month free. Find out why Close. İhsan Atasoy Hulasatul Hulasa1 adematmaz. Unsubscribe from adematmaz? 0.5 WEEKLY 0.5 WEEKLY https://www.bkmkitap.com/uc. /binnur-erdagi-doguer/hulasa-metin-sozluk/ 2019-05-12T08:20:35+00:00 0.9.

Key Features

• Lightweight 2-Channel DJ Controller
• Ideal For Beginner/Intermediate DJs
• Mixer Section With 3-Band EQ
• Integrated Soundcard (Audio Interface)
• Free Licence Copy Of Rekordbox DJ V5.3 Included

Questions? Email or call 1-888-202-8188

Pioneer DDJ-400 Rekordbox Controller Overview

The Pioneer DDJ-400 Rekordbox Controller is an affordable 2-channel DJ controller designed for use with Rekordbox DJ software (included). The DDJ-400 is the perfect starting point for anyone looking to get into DJ'ing whilst not compromising on versatility. The controller features an integrated sound card acting as an audio interface as well as performance controls such as the 16 pads designed for triggering samples and finger-drumming. The mixer section features a 3-band EQ on each channel, allowing you to blend between music seamlessly. The ergonomic layout makes mixing fun and easy, with in-depth controls such as a loop section and cue/loop call buttons.

Product Ref: 118744

Similar Products

Previous Image

• Pioneer DDJ-WeGO4 DJ Controller

• Native Instruments Traktor Kontrol S2 MK3

  $319.00

• Pioneer DJ DDJ-SB3 DJ Controller

• Roland DJ-202 DJ Controller

  $275.00

• Numark Mixtrack Pro III and Serato DJ Pro Bundle

Next Image

Full Description

View Full Description

2-Channel Rekordbox DJ Controller

The DDJ-400 is ideal for any aspiring DJ with this professional yet affordable DJ controller. The DDJ-400 is compact and sleek, jam-packed with performance controls and an integrated mixer. The 2-channel design features ultra-responsive jog wheels with low-latency performance. The ergonomic, club-style layout will get you familiarised with the standard design of most DJ controllers. This allows you to progress up to higher-end equipment, without it feeling like you have to completely learn the new design. The mixer section features 3-band EQ on each channel, allowing you to blend between songs to build your mixing skills. This controller is designed for use with the rekordbox DJ software. The controller comes complete with a free licence for the software, allowing you to get started straight out of the box.

16 Performance Pads & Loop Control

As well as the standard mixing controls, the Pioneer DDJ-400 includes a range of performance controls, designed to add flare to your performances. Features which have become standard on modern-day controllers include play/pause and cue buttons, tempo sliders and a loop section. There are also cue/loop call buttons, similar to the ones found on the CDJ-2000NXS2. Each channel features eight performance pads which can be used to trigger FX, shift the key of your song or for triggering samples. Above these are four other buttons: Hot Cue, beat Loop, Beat Jump and Sampler. These more advanced buttons are ideal for use when you have built up your mixing skills for a truly unique style.

Integrated Soundcard

One of the most unique features of the DDJ-400 is the integrated soundcard. The soundcard acts as an audio interface for the controller, eliminating the need for external equipment. The plug and play compatibility allows you to connect the controller to your computer and get setup within seconds. The unit is also USB bus powered, meaning the controller is powered via your USB connections on your computer for added convenience.

Applies to: ESET Internet Security, ESET NOD32 Antivirus, ESET Smart Security, ESET Smart. I activate with a License Key: my product is version 10 and later. Eset nod32 antivirus 9 64 bit license key.

Rekordbox Version 5.3

The Pioneer DDJ-400 comes complete with a free licence copy of Rekordbox DJ. The latest version of Rekordbox DJ (version 5.3) features a range of enhancements and upgrades. The software is what the controller uses to run music through, allowing you to build song libraries, learn how to DJ and sort your music archive. The tutorial feature within the software is useful for beginners, allowing you to learn the basics with clear and concise tutorials on your computer screen. A new ‘Track Suggestion’ feature also displays tracks that will match well with the song that is currently playing. This unlocks a new level of versatility, allowing you to preview mixes that you wouldn’t have normally thought of for added flexibility. You can also record, edit and share your mixes to social media, complete with track titles and time stamps using the software.

Design & Connectivity

The lightweight and compact design makes the DDJ-400 highly portable, perfect for the aspiring DJ on the move. The controller can be great for live DJ sets, house parties and practising at home, giving you everything you need to mix and blend songs. The front of the unit features a mic input circuit, allowing for MCs, hosts and other vocalists to join your set. The robust design provides optimal durability, and the unit includes grab handles on both sides making it easy to transport.

What’s Included

• DDJ-400 2-channel DJ controller
• USB cable
• Quick start guide
• Rekordbox dj licence key card

Features

• Ideal for beginner and intermediate DJs
• 2-channel DJ controller designed for rekordbox DJ software (free licence copy included)
• Integrated mixer with 3-band EQ
• Club-style layout
• Built-in sound card (audio interface) with plug and play compatibility
• Mic input circuit
• USB bus powered - class compliant
• Grab handles on both sides for easy transportation
• Ultra-responsive jog wheels for low-latency mixing

Specifications

• Software: rekordbox dj
• Frequency Response: 20 Hz to 20 kHz
• S/N Ratio: 103 dB (USB)
• Total Harmonic Distortion: 0.005
• Inputs: MIC x 1 (1/4-inch TS jack)
• Outputs: MASTER x 1 (RCA x 1)
• Phones: x 1 (3.5-mm stereo mini jack x 1)
• USB: USB (Type B) x 1
• Maximum Dimensions (W x D x H): 482.0 x 272.4 x 58.5 mm
• Weight: 2.1 kg

Related Products

Previous Image

• Gator G-CLUB CONTROL DJ Controller Bag, 19'

• Klotz RCA - RCA Cable Set, 3m

  $11.28

• UDG FlightCase DDJ-400/SB3/SB2/RB Plus (Laptop), Black

• UDG FlightCase DDJ-400/SB3/SB2/RB Plus (Laptop), Silver

  $171.00

Does Pioneer DDJ work with Traktor?

Can you use virtual DJ with DDJ