Graco pack n play with bassinet and changing table manual

See other formats

Read all instructions BEFORE 
assembly and use of this product. 

Keep instructions for future use. 

We recommend that you keep these instructions 
with your Pack 'N Play. A storage pocket has been 
provided for them on the bottom panel of your unit. 



® 



Graco 

Pack 'N Play 
Bassinet 



OWNER'S 
MANUAL 



® 




Model No. 
Serial No. 

Dear Customer, 
Please fill in the model and serial numbers 
above from the label in the center of the 
bottom of your new Pack 'N Play Bassinet. 

Models 9045, 9046, 9346, 9640, 
9643, 9716, 9726, 9741, 9743, 
9745 & 9746 



Congratulations on your purchase of a 
Graco® Pack 'N Play® Bassinet! 

Graco is the recognized leader in the design 
and manufacture of quality baby products. 
We believe your new Graco® Pack 'N Play® 
Bassinet is a wise choice, promising many 
hours of enjoyment for your baby. 

Your Pack 'N Play® may be used as a 
playard, portable crib or bassinet. 

Customer Satisfaction 

Our goal is to make every product the best 
it can be! We are also committed to supporting our 
products after purchase. If you would like to speak 
to Graco about your product, please contact our 
Customer Service Department at 1-800-345-4109 
or visit our Internet website, www.gracobaby.com. 
Our knowledgeable staff will be ready to answer 
any questions you may have concerning parts, use 
or maintenance. When you call, please have the 
model and serial numbers ready so your call 
may be processed quickly and efficiently. 



A WARNING 



Failure to follow 
instructions coul 



Setting Up the Pack 'N Play 

• THIS PRODUCT REQUIRES ADULT ASSEMBLY. 

• Keep fingers clear of top corners during setup. 

Be sure Pack 'N Play is completely set up before use. 
Check that the four top rails are completely latched, the 
center of the floor is pushed down, and the mattress is 
flat and secured by the velcro® straps. Always follow 
the instructions in the owner's manual to set up the 
Pack 'N Play. 

• When using the bassinet make sure velcro® patches 
underneath mattress firmly attach to bassinet mesh. 

• Before each use, inspect this product for damaged 
hardware, loose joints, missing parts or sharp edges. 
Do not use Pack 'N Play if any parts are missing 

or broken. Call 1-800-345-4109 for replacement parts 
or owner's manual. Do not substitute parts. 



Using the Pack 'N Play 

• The Pack 'N Play can be used as a playard, bassinet or 
sleeping crib. When used as a playard, never leave child 
unattended and always keep child in view. When used as 
a sleeping crib or bassinet, you must still provide the 
supervision necessary for the continued safety of your 
child. 

• Always keep the Pack 'N Play away from hazards in the 
area that may injure your child. 

• Do not add padding or other objects inside the Pack 'N 
Play that will permit your child to climb out. 

• Stop using this product when your child reaches 

35 inches (890 mm) in height, weighs more than 30 
pounds (14 kg), or is able to climb out. 

• Do not modify Pack 'N Play or add any attachments 
that are not listed in the owner's manual, including an 
add-on bassinet. 



Using the Bassinet 

• Use bassinet with only one child at a time. 

• The bassinet must be fully assembled and installed, 
including top rails, snaps and bottom pad, before using. 



A WARNING 



Failure to 
instructions coul 



© 1999 Graco 361-10-99 



2 



>w these warnings and the assembly 
Duld result in serious injury or death. 



• Discontinue using your bassinet if child weighs over 
15 lbs. (6.8 kg), can roll over, or can push up on hands 
and knees. 

• Never place a child under the bassinet. 

• DO NOT store the bassinet in the Pack 'N Play 
while in use. Store rails in pocket in the bassinet. 

• Never use a canopy with bassinet installed. 

Avoiding Suffocation Hazards 

• Unlike cribs that have rigid sides, the Pack 'N Play and 
the bassinet have flexible sides. As a result, the Pack 'N 
Play mattress is specially designed to prevent suffocation 
The Pack 'N Play mattress has a solid base, a certain 
length and width, and is less than one inch thick in order 
to meet safety standards. Using a thicker or a different 
sized mattress may allow a child's head to get between 
mattress and the side of the Pack 'N Play or bassinet 
causing suffocation. 

• To help prevent suffocation from entrapment, 

USE ONLY THE MATTRESS PROVIDED BY GRACO. 
Never use additional mattress or padding. 

• Never use plastic shipping bags or other plastic film as 
mattress covers not sold and intended for that purpose. 
They can cause suffocation. 

• Do not use a water mattress with the Pack 'N Play. 

Avoiding Strangulation Hazards 

• Strings and cords can cause strangulation. Keep strings 
and cords away from child. 

• Do not place the Pack 'N Play near a window where 
cords from blinds or drapes can strangle a child. 

• Do not hang strings on or over the Pack 'N Play. 

• Do not place items with a string around a child's neck, 
such as hood strings, pacifier cords, etc. 

• Do not attach strings to toys. 

This product is not intended for commercial use. 



to follow these warnings and 

juld result in serious injury or death. 



PACK 'N PLAY INSTRUCTIONS 

Setting up the Pack 'N Play® is easy, 
once you know how: 

To Set Up Your Pack 'N Play® 

Step 1. 

Undo the three velcro® 
straps. Fold velcro® straps 
back onto themselves. 

Set mattress aside. 
Step 2. 

IMPORTANT: Leave 
center of floor UP 
until all four top 
rails are latched. 

Grasp the bottom of 
of the top rails, and p 
up until you hear a "( 

Be sure top rails 
have become rigid. 

If not, pull up again 
until they are rigid. 

FOR SMOOTH SETUP and takedown, it's 
important to remember one thing: the center 
of the floor must be at least halfway up when 
locking OR unlocking rails (see picture below). 
Therefore: 

• When setting up, lock rails 

BEFORE lowering center. 

• When taking down, raise center halfway 

BEFORE unlocking rails. 

Step 3. 

Pull up the other two sides 
until they latch. 

If top rails do not latch, 
lift the center of the floor 
higher. Center of floor 
must be at least halfway 
up for the latches to 
catch properly. 

Be sure all top rails are 
rigid. 

Step 4. 

Hold one end of the 
unit up and push the 
center of the floor down. 







3 



4 



At first your Pack 'N Play may be like a new pair of 
shoes. You may need to break it in by slightly stretching 
the netting and fabric. If the center does not stay down, 
place some weight (several books) in the center of the 
unit and let it stand overnight. 



To Use as a 
Playard/Portable Crib 

Place mattress into your unit 
with padded side up. 

Always use your unit with 
mattress installed soft side up. 

Slide the two velcro® straps 
through slots in bottom of Pack 
'N Play and fasten to velcro® 
on underside. This will prevent 
mattress from moving. 

Your Pack 'N Play is ready to 
use. 




To Fold Your Pack 'N Play^ 



Step 1. 

Lower the back flap. Apply 
locks on wheels or casters, 
if present. Release the two 
velcro® straps under the 
Pack 'N Play, and remove the 
mattress. 



Step 2. 

IMPORTANT: 
Raise center halfway 
BEFORE unlocking 
rails. 

Grasp the red handle 
on the center of the floor 
as shown. 

Push down and turn 
handle. Then pull up 
approximately halfway 
to the top rails. 




Step 3. 

The top rail has a center piece 
with two tubes hidden under the 
fabric. The button on the bottom 
of the center piece releases the 
two tubes when it is pushed up. 



Center 
piece 

Tube 




( ^ 

Push UP button 
under fabric 



To fold the top rail: 

• Lift up slightly on the top rail. 

• Push up on the button located under 
the symbol to release the two tubes. 

• Push down. 
HINTS: 

• If top rails do not unlatch, lift 
the center of the floor higher. 

• Both tubes must be released 
for the top rail to fold. 



Step 4. 

Pull center up all the way. 




361-10-99 



Step 5. 

Gather your unit together. 
Do not force. 

If unit will not fold, look for a 
partially latched top rail. Squeeze 
the latch button to release the rail. 




Step 6. 

Find the bottom corner belt loop 
(only one). This loop is for holding 
unit and mattress together while 
carrying. 



Step 7. 

Wrap the mattress around your unit. 
Fasten together the velcro® straps, 
attaching the bottom strap to the 
bottom corner belt loop. 




r 



CARE AND MAINTENANCE 

FROM TIME TO TIME CHECK YOUR PACK 'N 
PLAY for worn parts, torn material or stitching. 
Replace or repair the parts as needed. Use only 
Graco® replacement parts. 

IF PACK 'N PLAY IS USED AT THE BEACH, you 

MUST clean sand off your Pack 'N Play, including 
the feet, before packing it into cover. Sand in top 
rail lock may damage it. 

TO CLEAN PACK 'N PLAY, use only household 
soap or detergent and warm water. 

TO WASH CARRY BAG AND FITTED SHEET, 

machine wash in lukewarm water on delicate 
cycle and drip-dry. NO BLEACH. 



To Cover Your Pack 'N Play® 

Models with changing table and wheels: 



Pull the cover over your unit 
as shown, making sure carry 
handle attached to Pack 'N 
Play mattress is lined up with 
zipper. 

Before pulling bag up, insert 
folded changing table into the 
side opposite the handle as 
shown. Pull bag up to cover 
end. Zip together. 



Models with wheels only 



Turn unit upside down, so that 
wheels point up. Pull the cover 
over your unit. Make sure carry 
handle attached to Pack 'N 
Play mattress is lined up with 
zipper. 

Push the plastic end of the bag 
over wheels and feet. Turn unit 
over and pull bag up to cover 
end. Zip together. 



Models with feet or 
casters and feet: 

Pull cover over your 
unit. Be sure carry 
handle attached to 
Pack 'N Play mattress 
is lined up with zipper. 
Turn unit over. Pull bag 
up to cover end. Zip 
together. 




Handle 




On certain models: 

The cargo bag opens on either end. Slip the bag over 
the Pack 'N Play. Check that the carrying handle 
attached to the Pack 'N Play mattress sticks out the 
hole in the bag. Zip both ends. 



BASSINET INSTRUCTIONS 



PARTS LIST 

CHECK that you have all the parts listed below 
BEFORE assembling your bassinet. 

No tools required. 




Bassinet 



33 



Loop end 



Tube (2) 



Wire end 



Red spring Tube (2) 

latch end 



Round end 



To Install Your Bassinet 



The four bassinet tubes are located in storage pockets 
sewn into the bassinet itself. 



Step 1. 

Insert wire end of one tube 
into the round end of a tube 
with a red spring latch. 

Repeat with other tubes. 




Step 2. 




Slide the assembled tubes 
into the tunnels on the sides 
of the bassinet. 



Step 3. 

Lift bassinet by the two tubes and lower it into the 
Pack 'N Play. Make sure the printed warnings on 
the end flap are facing up. 




Step 4. 

Install the end of the tube 
without the red spring latch 
by placing the loop end into 
the slot in the plastic corner. 



Step 5. 

On the other end of the tube, 
pull back on the red spring 
latch and insert the loop into 
the slot in the plastic corner. 



A WARNING The loop ends must be in the slots in the 
corners to secure the bassinet in the Pack 'N Play. Pull 
up on the tube and bassinet to ensure that the tube is 
in place. 

Step 6. 

Repeat steps 4 and 5 on the 
other side of the bassinet. 



Step 7. 

Snap both of the end flaps of 
the bassinet to the Pack 'N 
Play with the eight snaps 
(four on each end). 



Step 8. 

Place the mattress in the 
bassinet soft side up. Push 
down on the mattress to 
secure the mattress to the 
velcro® on the bassinet. 

DO NOT use your bassinet 
without the mattress 
provided by Graco. 



AWARNING To avoid SUFFOCATION, DO NOT use 
extra padding such as a water mattress, mattress, or 
pillows inside the bassinet. Use ONLY mattress 
provided by Graco. 

Your bassinet is now ready to use. 




361-10-99 



9 



10 



To Remove Your Bassinet 
Step 1. 

Remove the mattress from your bassinet. 
Step 2. 

Unsnap the end flaps from your Pack 'N Play. 
Step 3. 

Pull back the fabric at one corner of the bassinet to find the 
red spring latch. 



Step 4. 

Pull the red spring latch back 
and lift up the tube. 

Step 5. 

Pull the tube out of the bassinet 
and set aside. 



Step 6. 

Repeat steps 3, 4 and 5 to remove the other tube. 
Step 7. 



A WARNING Use extreme 

care when pulling the tubes /^>^ 

apart - '"'^y^ 

Pull the tubes apart by twisting 
the tubes as you pull. Store the 
tubes in the pockets in the 
bassinet. 





Casters* 

To apply the locks, push 
DOWN on the levers. 



To release the locks, lift UP 
on the levers. 



Wheels* 

To apply the locks, push 
DOWN on the levers. 

To release the locks, lift UP 
on the levers. 





Parent Organizer* 

A WARNING Always keep objects out of child's 
reach. Remove parent organizer when child is able 
to pull himself up in the Pack N Play. 



Step 1. 

Your parent organizer 
includes two plastic dividers. 

Slide the plastic dividers 
into the two pockets in the 
section dividers of the 
parent organizer. 




ACCESSORY INSTRUCTIONS 
ON CERTAIN MODELS* 

Side Flap* 

You can raise side flap if desired. 

Unfasten velcro® straps at 
bottom of flap. Roll flap up. 
Fasten in place with snap loops at 
top. 



Cargo Bag* 

The cargo bag can be snapped 
onto the end of the Pack 'N Play 
for easy access. Unzip both ends 
and tuck inside the bag. 
Maximum weight 5 lbs (2.3 kg). 




Step 2. 

Slide the tube into the 
mounts on the end of 
your unit. 

Push the button in to 
get it started. 

Pull up on the parent 
organizer to make sure 
that the buttons are 
caught on the bottom 



of the mounts. 



Button 



Step 3. 

To remove the parent 
organizer push in on the 
buttons on the bottom of 
the tubes and pull up. 




11 



12 



CHANGING TABLE INSTRUCTIONS 
(ON CERTAIN MODELS) 

Parts List 

CHECK that you have all parts listed below 
BEFORE assembling your changing table. 

No tools required. 



Long tube (2) 

C I £3 ^ 

Short tube (2) 




Changing pad 





Changing 
table 



Accessory bag 



To Use Your Changing Table 

A WARNING To protect your child from falls and 
other injuries: 

• Always stay within arm's reach of your child when 
using the changing table. Always use waist belt 
when child is on the changing table. Never leave 
child unattended. 

• The changing table is designed for use only with 
this Graco Pack 'N Play. Do not attempt to use it 
with any other product. Before each use, make 
sure the changing table is properly secured to 
the Pack 'N Play by pushing down firmly in the 
middle of the changing table. The changing table 
should not fall. 

• Do not use the changing table as a sleeping or 
play area. 

• Weight limit for the changing table is 25 pounds 
(11.3 kg). Do not use the changing table as extra 
storage. Always remove the changing table when 
your child is in the Pack 'N Play. 

• The Pack 'N Play changing table can be used on 
the floor without being attached to the Pack 'N 
Play. Never place the changing table on a piece of 
furniture, bed, counter or any raised surface from 
which the changing table or your child could fall. 



Step 1. 

Lay changing table flat on floor with short side in front 
of you and belt facing up. Gently slide one long tube into 
opening on long side exactly as shown. 

Repeat on other side. \ Long 




Step 2. 

Slide one short tube 
into opening on end 
as shown. 

For proper orientation, 
be sure folding side of 
hinge faces pad as 
shown. 

DO NOT insert 
other short tube 
at this time. 



Step 3. 

Turn up long tube so 
that its end points down. 

Insert end of long tube 
into opening on end of 
short tube as shown. 
DO NOT slide short 
tube up around the bend 
of long tube until you 
have finished next step. 

Make sure fabric does 
not get caught in 
opening when inserting 
long tube into short tube. 



Step 4. 

Repeat step 3 on other 
end of short tube, then 
slide short tube ends up 
onto long tubes. 

TO AVOID TEARING 
FABRIC, slide this end 
up before proceeding 
with step 5. 






Slide ends up 



361-10-99 



13 



14 



Step 5. 

Repeat steps 2 
and 3 on other end 
of changing table. 

If the short tubes 
have been inserted 
correctly, the changing 
table should be able 
to FOLD UP in the 
center as shown. 



Step 6. 

Place pad in changing 
table with vinyl side up. 
Pull belt straps through 
holes in center of pad. 




Step 7. 

Insert velcro® straps 
into the four slots at the 
corners of changing table 
and attach to velcro® 
on underside of changing 
table. This will prevent 
pad from moving. 



Fold up 





Step 8. 

Place changing table on 
Pack 'N Play as shown. 
You may use your changing 
table with or without your 
bassinet installed. Make 
sure tubes are securely 
over the sides of the 
Pack 'N Play. 

Check that the changing 
table is supported 
by the Pack 'N Play by 
pushing firmly down into 
center of changing table. 




To Use Accessory Bag 

If your bassinet is already installed, unsnap the four 
snaps on the bassinet end flap from either end of 
Pack 'N Play. 



Step 1. 

Snap accessory bag 
onto end of Pack 'N 
Play with four snaps 
as shown. 




Step 2. 

Snap bassinet end flap 
over the accessory bag 
with the four snaps. 




To Fold Changing Table 
Step 1. 



Pull up on waist belt 
straps to fold. 



Step 2. 

Ends of long tubes 
must point up when 
folded as shown. 



Ends of tubes_ 
point up 



Step 3. 

To carry or store your changing table 
with your folded Pack 'N Play, see 
"To Cover Your Pack 'N Play" section 
in these instructions. 




15 



16 



Replacement Parts 



Instructions for ordering Pack 'N Play R parts: 

Complete form below. Your Pack 'N Play model number 
MUST be included on the form to ensure proper replacement 
parts. Your model number can be found on a label on the 
center of the bottom of the unit. Payment must accompany 
your order. 



Parts List: 

Mattress 

Carry bag 

Cargo bag* 

Caster assembly* 

Wheels* 

Fitted sheet 

Bassinet parts: 

Bassinet 

Wire end tube 

Round end tube 

Changing table parts: 

Long tube* 

Short tube* 

Changing pad* 

Changing table* 

Accessory bag* 

* On certain models 



Price:** 

$17.50 
$15.00 
$15.00 

$ 5.00 (each)/$8.00 (2) 
$ 7.00 (each )/$1 0.00 (2) 
$10.00 

$17.00 
$ 5.00 
$ 5.00 

$ 9.00 
$ 7.00 
$10.00 
$15.00 
$ 7.00 

** Prices subject to change without notice. 



IF YOU NEED HELP 

If you have any questions or if you need any part not list- 
ed, please call toll-free: 
1-800-345-4109 
or visit our Internet website, www. gracobaby.com. 

Return the form below with payment to: 
GRACO CHILDREN'S PRODUCTS INC. 
CUSTOMER SERVICE DEPARTMENT 
P.O. BOX 100, MAIN STREET 
ELVERSON, PA 19520 



Model Number 

(Must be filled in) 

□ Mattress 

□ Carry bag 

□ Cargo bag 

□ Caster assembly 

□ Wheels 

□ Fitted sheet 

□ Bassinet 

□ Wire end tube 

□ Round end tube 

□ Long tube 

□ Short tube 

□ Changing pad 

□ Changing table 

□ Accessory bag 

Total: 



SHIP TO: 



Shipping 

& handling: 

6% sales tax 
(PA only): 

Total amount 
due: 



Name 



Address 



City, State, Zip 
L ) 



Telephone 

□ Check enclosed 
(payable to Graco Children's 
Products Inc.) 

□ Charge to credit card: 
□ Visa 

□ MasterCard 

~~ □ Discover 

$5.00 Account #: 



Expiration date:. 
Signature: 



361-10-99 



17 

Where is the model number on a pack n play?