Antigua and Barbuda, Aruba, Australia, Austria, Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Bermuda, Bolivia, Brazil, Brunei Darussalam, Bulgaria, Cambodia, Canada, Cayman Islands, Chile, Colombia, Costa Rica, Croatia, Republic of, Cyprus, Czech Republic, Denmark, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Estonia, Finland, France, French Guiana, Germany, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guernsey, Honduras, Hungary, Iceland, Indonesia, Ireland, Israel, Italy, Jamaica, Japan, Jersey, Jordan, Korea, South, Kuwait, Latvia, Liechtenstein, Lithuania, Luxembourg, Macau, Malaysia, Maldives, Malta, Martinique, Mexico, Monaco, Montserrat, Netherlands, New Zealand, Nicaragua, Norway, Oman, Pakistan, Panama, Paraguay, Peru, Philippines, Poland, Portugal, Qatar, Reunion, Romania, Saint Kitts-Nevis, Saint Lucia, Saudi Arabia, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Taiwan, Thailand, Trinidad and Tobago, Turks and Caicos Islands, United Arab Emirates, United Kingdom, United States, Vietnam VW Passat Tail Light Bulbs Replacement Guide
Owners of other VW Group vehicles such as the Beetle, CC, Tiguan, Golf, Touareg, Jetta, GTI, SportWagen, Eos, Rabbit, Bora, Vento, Lavida, Coccinelle, Maggiolino, Fusca, Audi A3, A4, S4, A6, S6, A7, A8, Q5, Q7, A5, S5, and TT may also find these DIY instructions to be helpful. The compatible replacement bulb part numbers are as follows: Brake & Rear Turn Signal # 7506, Reverse 921 (W16W) and Parking Lights # 2825. No tools are required to change the combination dual filament brake and rear turn signal light bulb. To access and replace the reverse and parking light bulbs, you'll need a 10mm socket with a 1/4" drive ratchet or a 10mm wrench or a flathead screwdriver and perhaps a plastic pry bar tool.  Pull Off Access Panel Power Plug & Fastener Slide Out Red Lock Tab The first two steps are to open the trunk and then move to the side of the sedan with the burnt out tail light bulb. Locate rectangular shaped fabric access cover on the fabric interior trunk liner. Gently pull off the access panel and set it aside in a safe place. Pull out the red plastic locking tab on the electrical connector. Push In Release Tab Pull Off Electrical Connector Rotate Counterclockwise Push in the release tab on the electrical connector before sliding the power plug straight off the rear of the tail light housing. Rotate the spring loaded thumb screw fastener in the counterclockwise direction to remove it. Spring Fastener Removed Pull Off Tail Light Housing Rear of Light Assembly Set the white plastic thumb screw aside in a safe place. Gently pull the tail light housing straight off the rear corner of the sedan. If you have trouble removing the housing, you may need to gently pry it off at the outer edge with a plastic pry bar tool. Gently Pry Back Clips Plastic Pry Bar Tool Pull Off Bracket Turn over the tail light housing and set it down on a towel to prevent from scratching the lens on your work bench or table. Use the plastic automotive panel pry bar toolor a small flathead screwdriver to gently push back the four red plastic retaining clips. Try to avoid using excessive force to prevent from breaking the retaining clips. Lift the grey plastic bulb bracket off the rear of the tail light assembly and turn it over to access the bulb. Push Down & 1/4 Turn CC Install New # 7506 Bulb Re-Attach Bulb Bracket Push the old dual filament combination brake and rear turn signal light bulb down in to the socket and rotate it 1/4 turn counterclockwise before pulling it straight out of the socket. Push a new # 7506light bulb in to the socket and rotate it 1/4 turn clockwise to secure it in place. Turn over the grey plastic bulb bracket and gently snap it back in to place on the rear of the tail light housing. Double check that all four of the red plastic retaining clips are secured to the bulb bracket. Line Up Tail Light Housing Button Head Mount & Slot Push On Tail Light Make sure that the red plastic slot near the outer edge of the housing is aligned with the button head mounting post on the vehicle. Line up the tail light housing with the rear corner of the car and slide it back in to place. Rotate Clockwise - Tighten Push In Power Plug Slide In Red Locking Tab Re-insert the white plastic fastener and tighten it in the clockwise direction to place tension on the spring until it is compressed by about half. Don't use a wrench or a screwdriver to tighten the tail light fastener to prevent from over tightening it and cracking the plastic housing. Push the power plug straight in to its socket until it "clicks" in to place. Slide in the red plastic locking to secure the power plug. Electrical Connector Secure Line Up Fabric Cover Replace Access Panel Line up the fabric access cover, re-insert the two tabs and then pop in the other edge. Trunk Lid Light Housing Plastic Access Cover Gently Pry Out Panel To access the reverse light and the two parking light bulbs, you will have to detach the trunk lid housing. Locate the rectangular shaped access cover on the underside of the trunk lid. Gently pry out the access panel with a flathead screwdriver or a plastic pry bar tool. Plastic Cover Removed Two Metal / Plastic Fasteners 10mm or Flathead Set the access cover aside in a safe place. To remove the two fasteners that secure the light housing to the trunk lid, you'll need either a flathead screwdriver or a 10mm socket with a 1/4" drive ratchet. Loosen Counterclockwise Pull Off Fastener 2nd Fastener Removed Set the two metal nuts with black plastic guides aside in a safe place. Slide Out Red Lock Tab Release Tab - Disconnect Plug Pull Off Light Housing Slide out the red plastic locking tab on the electrical connector with your fingernail or use a flathead screwdriver. Push in the release tab before sliding the power plug straight out of its socket. Lift the inner edge of the light housing and slide it off towards the outer edge. There is a curved lip on the outer edge of the light housing that is attached to the outer edge of the trunk lid. Lip - Attached To Outer Edge Rest Housing On Towel Gently Pull Back Clip Place a towel on your work bench or table to protect the plastic lens from being scratched. Gently pull back the two red plastic retaining clips to release the grey plastic bulb bracket. Lift Out Bulb Bracket Pull Out Old Light Bulbs Install New Light Bulbs Lift off the grey plastic bracket and turn it over to access the old bulbs. The larger bulb is the reverse (back up lamp) and the two small bulbs are the parking lights. Pull the old bulbs straight out of their socket and push in new ones. The reverse light bulb part number is 921 and the two parking lights are # 2825bulbs. (If you want brighter reverse lights, there are 921 LED options available.) Pop Bracket In Place Slide Lip On Outer Edge Lower Housing In Place Turn over the bulb bracket and push it down in to place. Make sure that the two red plastic retaining clips "click" over the bulb bracket. Slide the lip on the outer edge of the light housing on to the outside edge of the trunk lid. Lower the inner part of the housing until it is flush with the trunk lid. Line Up Fasteners Rotate Nut Clockwise Replace 2nd Fastener Line up the black plastic guides on the nuts with the rear of the light housing. Slide the fasteners in to place and spin the nuts a few turns in the clockwise direction to prevent them from becoming cross threaded. Push In Plug - Slide In Tab Tighten 10mm Clockwise Tighten 2nd Nut Tighten the two nuts in the clockwise direction with the 10mm socket and a 1/4" drive ratchet or a flathead screwdriver until they are snug. Try to avoid over tightening the nuts to prevent from cracking the plastic light housing. Push the power plug back in to its socket and slide in the red lock tab to secure it in place. Re-Insert Plastic Tabs Gently Snap In Access Cover Test New Tail Light Bulbs Line up the plastic access cover and gently pop it back in to place. Test the new tail light bulbs by having someone step on the brake pedal, activate the hazard signals and place the transmission in reverse. For more, check out all of my
Volkswagen Passat DIY Repair & Maintenance Guides. |
2014 vw passat rear turn signal bulb
Related Posts
Copyright © 2024 paraquee Inc.
